共找到 150 條與 管法蘭用非金屬平墊片 相關的標準，共 10 頁
Industrifal pipeword. Gaskets for flanged assemblies. Part 2 : non metallic flat gaskets (soft gaskets).
本標準規定了鋼制管法蘭(PN系列)用金屬包覆墊片的型式、尺寸、技術要求和標記。 本標準適用于HG/T 20592所規定的公稱壓力PN25~PN100的突面鋼制管法蘭用金屬包覆墊片
Metal jacketed gaskets for use with steel pipe flanges(PN designated)
本標準規定了鋼制管法蘭(Class系列)用金屬包覆墊片的型式、尺寸、技術要求和標記。 本標準適用于HG/T 20615所規定的公稱壓力Class300(PN50)和Class900(PN150)、工作溫度小于或等于150℃的突面鋼制管法蘭用金屬包覆墊片
Metal jacketed gaskets for use with steel pipe flanges(Class designated)
This European Standard specifies the dimensions and marking of IBC (inside bolt circle) non-metallic PTFE envelope gaskets for use with flanges
Flanges and their joints - Gaskets for Class-designated flanges - Part 3: Non-metallic PTFE envelope gaskets
Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 4: Corrugated flat or grooved metallic and filled metallic gaskets for use with steel flanges; German version EN 1514-4:1997
Metal-clad gaskets for steel pipe flanges (European system)
本標準規定了鋼制管法蘭(歐洲體系)用金屬包覆墊片的型式、尺寸和技術要求。 本標準適用于HG 20592所規定的公稱壓力PN為2.5MPa(25bar)～1O.0MPa(100bar)的突面鋼制管法蘭用金屬包覆墊片
Metal-clad gaskets for steel pipe flanges (European system)
Flanges and their joints - Gasket dimensions for PN designated flanges - Part 4: Corrugated, flat or ribbed metal gaskets and metal-plastic gaskets for use with steel flanges
Metal-clad gaskets for steel pipe flanges (American system)
本標準規定了鋼制管法蘭(美洲體系)用金屬包覆墊片的型式、尺寸和技術要求。 本標準適用于HG 20615所規定的公稱壓力PN為5.0MPa(Class 300)～15.0MPa～Class 900)的突面鋼制管法蘭用金屬包覆墊片
Metal-clad gaskets for steel pipe flanges (American system)
Flanges and their joints - Gaskets for class-designated flanges - Part 4: Corrugated, flat or grooved metallic and fillet metallic gaskets for use with steel flanges; German version EN 12560-4:2001
ADOPTED_FROM:EN 12560-4:2001 This standard specifies the dimensions, types, design and marking requirements of corrugated, flat or grooved metallic
Flanges and their joints — Gaskets for Class-designated flantes — Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges
本文件規定了給水排水管道水平定向鉆法施工用球墨鑄鐵管（簡稱拖拉管）及其接口的術語和定義，結構、接口、長度及允許偏差，技術要求，試驗方法，出廠檢驗，標志、包裝、存放、吊裝、運輸、安裝和質量證明書。 本文件適用于公稱規格為DN 100～DN 1200、包含有承口、插口及內部和外部涂
Ductile iron pipes for trenchless construction— part 2 : used for horizontal directional drilling method
Flanges and their joints - Dimensions of gaskets for PN designated flanges - Part 4: Corrugated, flat or grooved metallic and filled metallic gasketsfor use with steel flanges
ADOPTED_FROM:EN 1514-4:1997 This standard specifies the dimensions and marking of IBC (inside bolt circle) corrugated, flat or grooved metallic
Flanges and their joints — Dimensions of gaskets for PN-designated flanges — Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges
