共找到 150 條與 管法蘭用非金屬平墊片 相關的標準，共 10 頁
ADOPTED_FROM:EN 1514-4:1997 This standard specifies the dimensions and marking of IBC (inside bolt circle) corrugated, flat or grooved metallic
Flanges and their joints — Dimensions of gaskets for PN-designated flanges — Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges
Flanges and their joints - Dimensions of gaskets for PN designated flanges - Part 4: Corrugated, flat or grooved metallic and filled metallic gasketsfor use with steel flanges
Metal Jacketed Gaskets for Pipe Flanges and Heat Exchanger Flanges-Specification
Describes the application procedures for selecting and adjusting low-voltage overcurrent protective devices to achieve selective coordination. NECA
Recommended Practice for Installing Underground Nonmetallic Utility Duct (ANSI)
Describes the installation, shipping, and handling of underground single bore nonmetallic duct for power, lighting, signaling, and communications
Recommended Practice for Installing Underground Nonmetallic Utility Duct (ANSI)
This standard specifies the dimensions and marking of IBC (inside bolt circle) corrugated, flat or grovved metallic and filled metallic gaskets
Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges
Flanges and their joints - Gaskets for Class-designated flanges - Part 3 : non-metallic PTFE envelope gaskets.
GB/T19066 的本部分規定了PN標識的管法蘭用金屬波齒復合墊片(以下簡稱"波齒熱片>)的型式與代號,尺寸,技術要求,檢驗方法,檢驗規則,標記標志、包裝.運輸及貯存。本部分適用于公稱壓力為PN10~PN250、公稱尺寸為DN10~DN2 000 的波肯墊片
Composite wave-serrated metal gaskets for pipe flanges —— Part 1: PN designated
GB/T19066 的本部分規定了 Class標識的管法蘭用金屬波齒復合墊片 （以下簡稱 “波齒墊片 ”）的型式與代號，尺寸，技術要求，檢驗方法，檢驗規則，標記、標志、包裝、運輸及貯存。 本部分適用于公稱壓力為 Class150～Class1500、公稱尺寸為 DN15～DN600（NPS
Composite wave-serrated metal gaskets for pipe flanges —— Part 2:Class designated
GB/T39245 的本部分規定了 PN 標記的鋼制管法蘭用帶覆蓋層金屬齒形組合墊片（以下簡稱金屬齒形組合墊片）的型式及代號、尺寸、要求、檢驗、標記及標志、包裝及貯運。 本部分適用于公稱壓力不大于 PN160、公稱尺寸不大于 DN2000 的金屬齒形組合墊片
Grooved metal gaskets with covering layers for pipe flanges—Part 1：PN designated
GB/T 19675的本部分規定了管法蘭用金屬?zèng)_齒板柔性石墨復合墊片的型式、尺寸和標記。 本部分適用于PN2.5～PN50、DN 10～DN2000的管法蘭用金屬?zèng)_齒板柔性石墨復合墊片
Dimensions of flexible graphite gaskets reinforced with tanged metal sheet for pipe flanges
GB/T39245 的本部分規定了 Class標記的鋼制管法蘭用帶覆蓋層金屬齒形組合墊片（以下簡稱金屬齒形組合墊片）的型式及代號、尺寸、要求、檢驗、標記及標志、包裝及貯運。 本部分適用于公稱壓力不大于 Class2500、公稱尺寸不大于 DN1500（NPS60）的金屬齒形組合墊片
Grooved metal gaskets with covering layers for pipe flanges—Part 2：Class designated
Zpracovatel: Mod?anské strojírmy — ?KD, n. p., Mod?any u Prahy Pracovník ??adu pro normalizaci a mě?ení: Ladislav Vondra
Fiat sealing rings for flanged connections of pipe lines with tongues and grooves - Np 10 - Np 100
Basis for calculation of aluminium alloy Pipe flanges with full face gasket
FLANGES AND THEIR JOINTS. DIMENSIONS OF GASKETS FOR PN-DESIGNATED FLANGES. PART 4: CORRUGATED, FLAT OR GROOVED METALLIC AND FILLED METALLIC GASKETS FOR USE WITH STEEL FLANGES.
