共找到 150 條與 管法蘭用非金屬平墊片 相關的標準，共 10 頁
Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts
本標準規定了管路法蘭用金屬齒形墊片（以下簡稱齒形墊片）的型式及代號、尺寸、要求、檢驗、標記及標志、包裝及貯運。本標準適用于JB/T 79、JB/T 81、JB/T 82、JB/T 84和JB/T 86中規定的公稱壓力PN16~PN200的齒形墊片
Serrated metal gaskets for pipe flanges
Specifies dimensions of inside bolt circle and full face gaskets for use with flanges to BS 4504. Full account has been taken of European standards
Specification for dimensions of gaskets for pipe flanges to BS 4504-Dimensions of non-metallic gaskets for pressures up to 64 bar
本文件規定了用于EN 1759-1、EN 1759-3和EN 1759-4法蘭的非金屬材料平墊片的尺寸、形狀、名稱和標記，適用于Class 150、Class 300、Class 600和Class 900，公稱直徑DN 15至DN 600。此外，本文件還包含常見材料及其標記的說明
Flanges and their joints - Dimensions of gaskets for Class-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts
本標準規定了鋼制管法蘭用金屬齒形墊片的型式、尺寸和技術要求。 本標準適用于JB/T 79、JB/T 82中規定的公稱壓力pN為4.0～16.0MPa的凹凸面整體鑄鋼管法蘭和對焊鋼制管法蘭用金屬齒形墊片
Metal dentate gaskets for pipeline flanges
Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts
Flanges and their assemblies - Gasket dimensions for PN designated flanges - Part 1: Non-metallic flat gaskets with or without insert
La norma stabilisce le dimensioni e la marcatura delle guarnizioni piatte non metalliche, con o senza inserti, per impiego con le flange conformi al
Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts.
Draft Document - Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts; German and English version prEN 1514-1:2023
FLANGES AND THEIR JOINTS. DIMENSIONS OF GASKETS FOR PN-DESIGNATED FLANGES. PART 1: NON-METALLIC FLAT GASKETS WITH OR WITHOUT INSERTS.
This European Standard defines the requirements for the determination of the flatness of monolithic glass transparencies for aircraft applications
Aerospace series - Non-metallic materials - Glass transparencies - Test methods - Determination of flatness
Method of test for magnetic properties of amorphous metals using single sheet specimen
Dimensions and marking of IBC gaskets for nominal pressures PN10, PN16, PN25 and PN40 and for nominal sizes up to and including DN 900
Dimensions of gaskets for flanges to BS 4504-Specification for corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges
Flanges and their joints - Dimensions of gaskets for Class-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts
La norma specifica le dimensioni, i tipi, la designazione e la marcatura delle guarnizioni piatte non metalliche, con o senza inserto, per flange
Flanges and their joints - Dimensions of gaskets for Class-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts.
