GM GMP.PBT.024-1999 PBT 20% 玻璃纖維增強，阻燃（V-0）

PBT - 20% Glass Fiber Reinforced, Flame Retardent (V-0)

GM GMP.PA66.058-1998 25%玻璃纖維增強阻燃劑(v-0)尼龍66

Nylon 66 - 25% Glass Fiber Reinforced, Flame Retardant (V-0) (Revision E)

GM GMP.PBT.025-1998 PBT 40% 玻璃纖維增強/礦物填充，阻燃（V-0）

PBT - 40% Glass Fiber Reinforced/Mineral Filled, Flame Retardant (V-0)

GM GMP.PBTP.029-1998 PBTP 30% 玻璃纖維增強，阻燃（V-0）被 GMP.PBT.029 取代

PBTP - 30% Glass Fiber Reinforced, Flame Retardant (V-0) Replaced By GMP.PBT.029

GM GMP.PBTP.024-1999 PBTP 20% 玻璃纖維增強，阻燃劑（V-0）被 GMP.PBT.024 取代

PBTP - 20% Glass Fiber Reinforced, Flame Retardant (V-0) Replaced by GMP.PBT.024

GM GMP.PBTP.027-1994 30%玻璃纖維增強阻燃劑(v-0)聚對苯甲酸丁醇酯

PBTP - 30% Glass Fiber Reinforced, Flame Retardant (V-2)

GM GMP.PBTP.005-1995 30%玻璃纖維增強阻燃劑(v-0)聚對苯甲酸丁醇酯

PBTP - 30% Glass Fiber Reinforced, Flame Retardant (V-0)

GM GMP.PBT.029-1998 30%玻璃纖維增強阻燃劑(v-0)聚對苯二甲酸丁二醇酯

PBT - 30% Glass Fiber Reinforced, Flame Retardant (V-0)

GM GMP.PBTP.025-1998 PBTP 40% 玻璃纖維增強/礦物填充，阻燃劑（V-0）被 GMP.PBT.025 取代

PBTP - 40% Glass Fiber Reinforced/Mineral Filled, Flame Retardant (V-0) Replaced by GMP.PBT.025

GM GMP.PETP.001-1995 30%玻璃纖維增強阻燃的(v-0)聚對苯二甲酸乙二醇酯

PETP - 30% Glass Fiber Reinforced, Flame Retardant (V-0)

09/30201778 DC BS 2HR 52 耐熱鋼坯、棒材、鍛件及零件規范（Ni 25 5、Cr 14 7、Ti 1 8、Mn 1 5、Mo 1 2、V 0 3）

Cross References: BS HR 100 EN 4500-1 EN 4500-3

BS 2HR 52. Specification for heat-resisting steel billets, bars, forgings and parts (Ni 25.5, Cr 14.7, Ti 1.8, Mn 1.5, Mo 1.2, V 0.3)

09/30201774 DC BS 2HR 51 高膨脹耐熱鋼坯、棒材、鍛件及零件規范（Ni 25 5、Cr 15、Ti 2、Mn 1 5、Mo 1 25、Si 0 7、V 0 3）（980 攝氏度溶液處理）

Cross References: BS HR 100 EN 4500-1 EN 4500-3

BS 2HR 51. Specification for high expansion heat-resisting steel billets, bars, forgings and parts (Ni 25.5, Cr 15, Ti 2, Mn 1. 5, Mo 1.25, Si 0.7, V 0.3) (Solution treated at 980 degreesC)

10/30230595 DC BS 2HR 650 制造螺栓、螺柱、緊定螺釘和螺母用高膨脹耐熱鋼棒材和線材規范（Ni 25 5、Cr 15、Ti 2、Mn 1 5、Mo 1 25、Si 0 7、V 0 3）（極限標尺截面 20 毫米）

Cross References: BS HR 100 EN 4500-1 EN 4500-3

BS 2HR 650. Specification for high expansion heat-resisting steel bar and wire for the manufacture of bolts, studs, set screws and nuts (Ni 25.5, Cr 15, Ti 2, Mn 1.5, Mo 1.25, Si 0.7, V 0.3) (Limiting ruling section 20 mm)

10/30238238 DC BS 2HR 650 制造螺栓、螺柱、緊定螺釘和螺母用高膨脹耐熱鋼棒材和線材規范（Ni 25 5、Cr 15、Ti 2、Mn 1 5、Mo 1 25、Si 0 7、V 0 3）（極限標尺截面 50 毫米）

Cross References: BS HR 100 BS EN 2398 BS EN 2399 EN 4500-1 EN 4500-3

BS 2HR 650. Specification for high expansion heat-resisting steel bar and wire for the manufacture of bolts, studs, set screws and nuts (Ni 25.5, Cr 15, Ti 2, Mn 1.5, Mo 1.25, Si 0.7, V 0.3) (Limiting ruling section 50 mm)

ITU-R V.2130-0-2019 術語和定義的準備指南

Guidelines for the preparation of terms and definitions